sonic crayon

FB

2011-10-08T15:37:00.000-07:00

Sonic Crayon FX now has a FB page. Should make updates and info easier..

http://www.facebook.com/pages/Sonic-Crayon-FX/230721366984881

HE v2 "sampling" mode brainstorm

2011-06-03T18:46:00.000-07:00

Is a glitchy "sampling" mode on the new HE better than no "sampling" mode at all? The intent is to have a mode that records sound input and turns it into an envilope. Here's how I'm doing it so far:

20 sub-samples are taken from the input at 5ms intervals, then averaged. the average becomes the main "sample" that lasts 100ms. this occurs 10 times a second.

so it samples at a total of 200hz. the problem is when I hit a note like low E (82-ish hz), or any note really, that the played note will get pretty close in-phase with my sampling frequency from time to time as it "drifts". because of that, for an entire 100-200 milliseconds, it'll only be sampling the "dips" in-between the sound waves and will average close to 0, even though to our ears the note rings loud and clear. as clear as it was when it was sampling at the peaks of the same waves 300ms earlier! the result is a stuttery glitchy envelope instead of smooth envelope following.

adding circuitry is a last resort (there's barely any room left on the PCB). so far I've tried:

1. adding offsets of 2.5ms every 2 samples to try and average an equal number of wave dips and peaks.

2. only keeping the very highest sample out of 20

3. ignoring sudden drops of envelope if the next one goes right back up again (loss of detail)

Increasing the sampling frequency is difficult at the moment since the whole foundation of the bare-bones design is built around 20 sub-samples per "real" sample, because of the interpolation I'm doing. I think I'll try adding a timer interrupt that samples much more/faster and independantly of the rest of the program.

Hollow Earth prototype

2011-05-26T14:53:00.000-07:00

v2.0 prototype. It works really well! Things left to do on firmware is the sample-from-sound-and-turn-into-LFO mode, a dedicated random mode, and some tweaks to the simple random blend you can add to existing LFOs.

Mockup

2011-04-28T22:19:00.000-07:00

1:21 AM blog post! Just a graphic mockup of what I think the new hollow earth will probably look like.

Oh yeah, just got back from seeing Godspeed You! Black Emperor, that was pretty fantastic!

/random

Hollow Earth redesign proto

2011-04-24T10:05:00.000-07:00

Found the time to (mostly) finish the new prototype this weekend. What's left to be done is ironing out the few glitches and adding a couple modes in software. Specifically:

-menu to assign a function to the soft-stomp.
between tap tempo, shape record and manually triggered envelope

-a mode where it samples and makes an lfo/envelope based on
input sound. could be pretty rad for drum machine stuff!

-I should probably make an option to invert whatever shape

...oh yeah, and definitely what's my densest/most insane PCB layout. It'll take a few weeks to arrive, though.

1165 lines of code..

2011-03-27T15:25:00.000-07:00

..though a bunch of it was copy pasted. I figure I'm about 95% done the new hollow earth, at least programming-wise. Hardware-wise, an AVR dev board, a few rotary encoders, a trimpot, an led and a 5x7 led matrix is all I've been staring at these past few weeks.

Four knobs is probably all you'll need! They're all multi-function. Turn for one thing, hold down and turn for another, tap for another, etc.

A bit of tech info. I'm using an atmega644 uC. It's got 64KB program memory but so far I'm using only 17% of it. I needed the 2KB of eeprom it offered for preset storage. When recording custom LFO shapes, it samples at 10 a second for up to 18 seconds. And then it's interpolated times 20 to smooth it out. Speed is full adjustable while recording and after, obviously. 10sps is plenty for slow human hands, but I'll offer the user to fine tune this in a sort of "preferences" mode.

Let's see, checklist. What's done, and to-do..

(software)
-expressive display
-hook up PWM output (with freq doubling)
-do custom LFO record/playback
-x20 interpolation!
-speed control
-tap-tempo
-depth control
-random blend
-preset saving/loading
-square/triangle/ramp/sine/saw hard preset LFOs
-shape edit
-trigger mode
-multimode tap footswitch
-preferences/options

(hardware)
-LDR biasing
-power filtering
-clean tl074 buffer
-CV out
-polarity protection

led matrix visual feedback

2011-03-19T09:00:00.000-07:00

clicky encoders are annoying. ordered some non-clicky ones.

with the push-for-secondary-function knobs and the display now offering an expressive level of visual feedback, I've been able to simplify the next hollow earth pedal to just 4 push-knobs and one toggle at the back of the enclosure!

this was a huge priority because it means I can PCB mount everything on a single board this time!

LED matrix app

2011-03-13T13:02:00.000-07:00

So I got myself a couple tiny 5x7 LED matrix displays to tinker around with. I thought they might be a nice replacement to 7-segment displays. On the new Hollow Earth, I'm using a microcontroller with a greater number of pins, so I think it's doable. Might make for some neat animation, too!

Then my mind caved in at the thought of manually typing binary data for each PIXEL. It's pretty daunting to do by hand, because each LED in the matrix does NOT have its own pin. Instead it's a row and column array where you have to carefully "render" the LEDs, line by line, applying positive power to cathodes where you *don't* want pixels, and so on. Arrrrghhhhhhhhhhhhhhhhhh..........

Too much, I said, so what do I do? I install something I haven't used in like ten years, Visual Basic 4.0.

An hour later, I have made an app where I can draw a number, letter or graphic just by clicking on squares, and then automagically spits out code and/or raw binary data I can simply paste in my micro!

Whatta time saver!

Writing a program that writes code for you. How zen!

Redesigning a fundamentally awkward design..

2011-03-02T09:03:00.000-08:00

so yeah..

I've started a complete Hollow Earth redesign. I really want to see it being sold again and the old design was just so difficult. Being on two PCBs, socketed ribbon cables, wired switches, hacks and tricks giving each build it's own little quirks. I've had enough of all that. The old one was designed when I was just beginning to understand microcontrollers almost two years ago and I've learned a lot since. Time to do it right, this time.

Instead:
-single PCB design
-everything PCB mounted, except jacks
-rotary encoders instead of pots, with double functions
(turn does one thing, push and turn does another, or just push, like tapping the speed knob for tap tempo)
-less parts (no "shape" stompswitch for one)
-in-program interpolation, no more smooth knob
-and so on

Probably no more vactrols either. They were a pain to bias properly so that CV-out and the actual tremolo effect played nicely together. Gonna try digital potentiometers instead.

UPDATE: I'm afraid trigger mode will probably go the way of the dodo. It never worked THAT great, and it's one of the major roadblocks in my simplifying.

OT: New music website thingie..

2010-12-21T12:21:00.000-08:00

I've finished a new website for my various musical projects (not really DIY-related). So now instead of pointing people to a myspace, I can just send them to this:

www.dronecloud.org

Crushed Glass granular sampler/looper/glitcher

2010-12-12T12:17:00.000-08:00

This is something I've been working on (on-and-off) since january or febuary of '10. For DIYers, looping is usually restricted to ISD sound recorder chips. They are neat but don't offer a whole lot of flexibility. I wanted totally random access to individual samples for some pseudo-granular drones so I saw what I could do with microcontrollers. Initially I had started learning dsPICs, but later put it aside and went with what I knew, the 8bit AVR.

I'm using SPI RAM which isn't the fastest solution but I just wanted to see if my ideas could be done. Fidelity was secondary. I went with the ATMEGA328 which is the chip with the most amount of internal RAM in DIP format. I didn't want to use the larger 40-pin DIPs.

I wanted to be able to ping-pong the "playback head" in as little time as a 1ms sample window, define start and end loop points, among other things. That meant quite a bit more code that simple record and playback. Keeping it tight, I still manage up to 12KHz sampling on the 8-bit uC. Considering there's a lot of SPI communication with both RAM chips and the DAC, I don't think that's too bad. Stuff like LED updates and potentiometer sampling only happen around 20 times a second. I use an additional uC (atmega88) on a daughter board for the 16 LEDs. It serves as a 4-to-16 decoder.

On the less technical side, sound-wise it is pretty lofi. It doesn't handle complex recordings well. Stuff like full chords, mixed-down songs, things with a lot of harmonic detail and smooth volume dynamics. Some complex things work, most don't. What it does handle well is individual monophonic instruments (or picking single strings on a guitar), some vocals, cicuit bend noises, and it handles electronic beats really well!

The controls are really counter-intuitive, and for this reason I won't be building these for anybody just yet. There are some bugs and limitations that I have not been able to fix in the weeks and months of work. The problem is that I designed this back-to-front which is a really bad way of doing things. I started building a looper then later tacked on features. It's all duck-taped and bandaided together with tricks and hacks in the code. What I should of done is figure out my features first, then design around that. Because I did the reverse, fixing the bugs and limitations have been so difficult that I'll have to start over if I intend to sell these. Personally I can live with these quirks, but I can't help but think others would be confused.

The next one will be much better!

A list of features/controls, some more technical information and a video below.

- Input gain (with red clipping LED)
- Independent Dry and Wet knobs
- Record / Playback toggle switch (with purple rec LED)
- Hard bypass toggle switch (with orange LED)
- Low pass filter
- 16 LED "head" position
- Speed, sets the samplerate
- Start and End realtime sample trimming
- Trim drift/gradual offset
- Confusion knob which does ping pong stuff to the "head"
- Direction knob sets forward or reverse, or glitchy in-between madness!

Main CPU: ATMEGA328 (overclocked to 12mhz at 3.3v)
Secondary CPU: ATMEGA88 (for 16 LEDs only)
ADC: internal 8bit
DAC: external 12bit MCP4921
RAM: two 23k256 ICs
LPF: MAX7403
Programmed in BASCOM

Thanks for reading/watching!

3 bitcrushers for sale SOLD

2010-06-12T11:36:00.000-07:00

as of now.

$150 US
tracked and insured shipping is around $15 to north america. contact me if elsewhere.

Check the blog post down below. Some samples are there. has samplerate reduction, bitcrushing on an 8-position knob, wet/dry blend and volume. good for lo-fi effects, nintendo/atari sounds, weird digital fuzz, glitches, etc. great on synths and drum machines too! does a good job killing fidelity! when turning up the volume and harshness, with the wet/dry knob all the way "dry", it's not totally dry. more like 96% dry. uses 9v DC standard boss-like adapter. not included. Meant as a non-subtle effect but subtle can sort of be dialed in. Full refund if you dont like it (assuming it's in okay condition, and minus shipping). will try and ship before monday.

*SOLD*

Moth bitcrusher sale

2010-06-10T16:02:00.000-07:00

I'll have three bitcrushers for sale in a few days.

two samples. both tentatively co-titled the-art-of-dicking-around. I have no idea what I'm doing. I've never been good at recording dirt-only stuff, at least without some kind of backing.

http://nearworlds.org/stuff/diy/moth1.mp3
http://nearworlds.org/stuff/diy/moth2.mp3

they'll officially go on sale sometime on saturday for $150 US each, but only as of when I update this blog on that day saying so. so please no emails ahead of time. when the time comes, you can reach me at:

eblythe (aaaat) mochamail (dooooot) com

moth PCBs are in

2010-05-21T19:26:00.001-07:00

Sonic Crayon Moth + Hollow Earth plans

2010-04-29T18:37:00.000-07:00

hookay....

Things have been lagging due mostly to demotivation re: the hollow earth. That sucker is tough to build, I mean really tough. it's definatelly not dead, though, and as a way to help kick-start things back up again, I'm selling off a batch of bitcrushers/samplerate reducers with wet/dry blend control. it's an easy build I'll have no trouble building a dozen of, and at the same time it'll help refinance the whole hollow earth gig.

So here's the bitcrusher, called the Moth and does 1-8 bit crushing and samplerate reduction. there's wet/dry blending and volume as well. the graphic will change a little. here's a bad clip. I'll do a youtube once things are orginized.

there will be no reservation list for this one. in a bunch of weeks I'll just announce a day they go on sale and that'll be that. $150 a pop.

in semi related news, the kind folk at Audio Effekte have written a kind word on this project of mine, as well as about montreal assembly!

read it here

You should check out Scott's stuff (at mtl assembly). he makes rad effects too and his bitcrushers are way more versatile than mine! face-melting boxes galore!

Meanwhile..

2010-04-03T21:49:00.000-07:00

..I'm thinking of doing a small run (10) of simple samplerate reduction pedals to try and kick things back up again. Two knobs (blend and samplerate), simple circuit, etc. 10x easier than the hollow earth and would help fund/re-enthusiate an eventual hollow earth reincarnation.

Maybe.

Hollow Earth non-update

2010-03-23T20:57:00.001-07:00

I'm super late with Hollow Earth orders, in case you were wondering.
big surprise

of floopers and bitcrushers

2010-02-14T18:42:00.000-08:00

A quick flooper (feedback looper) I built for the Pines. Saw it in action at a show last night, awesome!

Also, an old video of that bitcrusher I forgot ever existed:

DIY Synth log #2

2010-01-31T17:49:00.000-08:00

Little board I made to help me in developping the programmable synth. Seeing how so many things need to be controlled by DACs (for preset recall and automation), made a little 16-channel multiplexer with sample-and-hold.

Still shopping around for a simple 16-bit DAC. most are either SMD, or are I2S (too slow) instead of SPI. And I can't spare the pins for parallel. Eugh...

DIY Synth log #1

2010-01-10T07:35:00.000-08:00

Some sounds I had lying around:

http://nearworlds.org/stuff/diy/diy_synth_01.mp3
http://nearworlds.org/stuff/diy/diy_synth_02.mp3

Part of a long-term project of building a synth. The rough outline is:

-3 or 4 oscillators. sine, square, triangle, ramp
-2 or 3 LFOs for FM, AM and VCF
-1 noise generator
-lots of LFO shapes, including "manual" waveshaping
-resonant VCF (using SSM2044)
-2 ADSRs for amplitude and VCF
-programmable delay (based on 2399)
-savable patches
-real wood enclosure and 2-octave keybed!
-some kind of basic arpeggio/sequencer
-MIDI-in a big maybe. I haven't looked at MIDI yet

I'm using DSI-type synths (evolver, prophet) as inflluence for the design. Digital control of analog stuff! In the sounds above, I'm using a atmega88 microcontroller to drive an MCP4921 DAC which in turn drives an analog XR2206 function generator. The 12-bit resolution of the DAC gives me a range between 30hz to around 8khz with tolerable drift. The micro has a table of all DAC values for 92 notes. The samples are straight from the oscillator. There's no envelope, filter, LFO or anything. The delay in the first one was added in soundforge for kicks. The "sequencing" is hard-coded in the micro.

The XR2206 is basically a voltage-controlled oscillator with sine/triangle/square outputs, and ramp with a bit of tweaking. It's really simple to use and requires almost no external components!

I'm gonna need a lot of DACs. One for each oscillator, for each LFO/ADSR combo. I intend to do the LFOs and ADSRs in code to make them flexible and as low-part-count as possible! I think I can mix both LFO and ADSR in code and have it use just one DAC.

I'm hoping to make the delay as dynamic as possible! Time and decay modulated by keys and LFOs and whatnot! If I can fit all components for a single "voice" (a dozen chips, I'm guessing) i nsmall-enough space, then I might consider making this a 4-voice synth. The main micro would just have to keep track of which voices are available, and if none are, use the one that was pressed the longest time ago.

I don't know yet if I want to salvage a wooden enclosure from something or just make my own. I haven't done any sort of woodworking since when I was a kid. It's not hard, but I am sort of ill-equipped! I'm not worried for the keybed. Doepfer has some nice OEM ones.

Next batch..

2009-12-26T07:41:00.000-08:00

Having major issues with the new batch of PCBs. Can't figure out what it is. If I ever do find out what it is, and if it's serious, then the next batch will be delayed another two months, and a lot of wasted money.

I wish I could drop everything.

Hollow Earth orders

2009-12-24T17:18:00.000-08:00

Hi,
I am no longer taking orders for the Hollow Earth. I need to get through the current list. This thing has been too much of a time eater, cost and source of stress, and I need to figure out what to do.

new HE PCBs are in

2009-12-15T18:01:00.000-08:00

4'th revision Hollow Earth PCBs are finally in (7 week wait, ughhh), so I'll get started on builds #12-18 shortly.

fixes include using surface-mount switches instead, some additional noise filtering (not that it was much of a problem before), volume adjustments, and stuff that'll make building them easier for me.

vibrato

2009-11-30T17:49:00.000-08:00

vibrato I built for someone. design similar to the one I made months ago (down the blog) with some improvments/bugfixes.

and yes, still making Hollow Earths. it's just taking time to get through thel ist is all. and yes as of 2010 they will be $275 instead of $200. I underestimated the cost in time and materials when I initially started making them. sorry about that. people on the list have already been informed.

scope!

2009-11-25T09:29:00.001-08:00

Eight Bit Organism

2009-11-08T15:23:00.001-08:00

here's a lame-ass demo. I'm playing a discarded umbrella into a TV that's on fire.

It's a bunch of stuff. A bitcrusher, samplerate reducer, a granular sampler/repeater/glitcher, a harsh digital fuzz and noise source. Controls are as follows (left to right):

top:
[B]bitdepth[/B]: bitcrush from 8 to 1 bit. things get noisy and ugly and awesome!
[B]samplerate[/B]: rate reduction, atari/nintendo-ish sounds, etc
[B]tone[/B]: just a big muff tonestack. middle is neutral. right is high boost, left is low boost.
[B]blend[/B]: wet-dry blend
[B]volume[/B]: makes the pedal vomit kittens

bottom:
[B]grain size[/B]: sample size of the granular sampling buffer.
[B]grain mod[/B]: modulates the grain sample up or down in pitch
[B]glitch 1 and glitch 2[/B]: makes it stutter in different ways. the toggle switch at the top makes the soft-stomp on the right active one or the other of the buttons.

Digital garbage

2009-11-01T16:20:00.001-08:00

Today I worked on cheap granular synthesis, bitcrushing and samplerate reduction, all at once. It sounds like the world caving in!

Custom-painted Hollow Earth up on eBay

2009-10-21T18:19:00.000-07:00

Custom-painted Sonic Crayon FX Hollow Earth. s/n #011

Starting bid $150. Ends in one week.
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=200397194730

Custom painted Hollow Earth

2009-10-19T16:04:00.000-07:00

I'm still selling a small handful of these a month, and hopefully I can optimzie production a little to be able to squeeze a few more in that timeframe. Getting through the waitlist, slowly but surely...

I'm building a custom-painted Hollow Earth that I'll be putting on ebay soonish. Hopefully before the end of the week. It's functionally no different from the vanilla ones, but it'll be pretty with swirlies and specks on it. See it as an experiment, testing the auction waters on a custom item.

fun with graphic LCDs!

2009-09-26T19:42:00.000-07:00

Got this graphic LCD from MC Shop, the DX-160. Wedged it inside a bare-bones Hollow Earth with a basic UI to see the potential!

Maybe I'll build a simple synth/drone box with manually drawable waveforms too.

I'm also clocking the AVR chip a lot fastern ow, 20MHz. I could get it to update the screen a lot faster, but I don't want it to drain juice needed for other stuff.

domain

2009-09-09T15:40:00.001-07:00

www.soniccrayonfx.com

potentially new Hollow Earth features..

2009-09-06T05:57:00.001-07:00

I'm trying to squeeze the most out of this design. I've had a few feature requests and a lot of them were tap-tempo. Harmony-Central user crxsh had a good idea about making the soft-stomp, the one used for recording of shapes, multi-function. Specifically, being able to toggle it between record, tap-tempo and bank select.

I'm gonna see how feasable this is. It won't be ready for the next few batches as I still have PCBs to use up. Testing and optimizations also take time. But hopefully I'll get those to work. A three-way toggle switch could be placed on the side of the box next to the soft-stomp with a label describing the three states.

Another issue the Hollow Earth seems to have is that expression-out doesn't work with every pedal with expression-in, only some of them! I never intended it to be a main feature, just as a fun extra, but it seems more people want to use it than I had previously thought. I'll try and put some effort into increasing the compatibility of exp-out.

For the geeks, an expression pedal is basically a potentiometer. Potentiometers have three lugs, one for the minimum range, the max range, and the wiper. The way the Hollow Earth outputs expression control is by controlling an LED-LDR combo (an electrically-controlled pot), which due to its nature is the equivalent of an only 2-lug pot. While this works with many pedals with an expression-in jack, it doesn't work with those expecting 3-full lugs. So far, this includes the Eventide Timefactor and EHX HOG. I'll do my best to fix this in a later revision.

Vibrato build, more Hollow Earth stuff..

2009-08-29T18:12:00.000-07:00

Here's a vibrato I built semi-recently. It's based on a PT2399 delay chip and I use an AVR micro with a few wavetables to generate LFO shapes.

An update on the Hollow Earth. As explained in a mass email, I'm moving to a waitlist scheme. So I've asked everyone on the notification list to email me again, and I will use that order. I've already been in contact with the four for the next batch (very soon). In the meantime, here's a video demo by user crxshdxmmy showing some examples of traditional trem and some pattern variations:

First batch sold out!

2009-07-25T14:28:00.000-07:00

Thanks to everyone for the support!

Stay tuned for more information on the next batches and stuff.

Hollow Earth "product" page

2009-07-24T14:38:00.001-07:00

http://nearworlds.org/soniccrayon/hollow_earth.html

Hopefully this will answer some questions.

Hollow Earth batch next Saturday

2009-07-20T08:38:00.000-07:00

Just a heads up! I'll be selling four of these next saturday
(25th of july) starting noon eastern-time. As of that time,
I'll pick the first four emails who tell me they are able
to pay right away. Please don't send me money untill I've
confirmed you're one of the four. Payment will be paypal
and is the sum of $200 US, not including shipping. I'll ship
via regular mail (like USPS) from Canada. No Fedex or UPS, they're
problematic for me.

If there are any questions before then I'll do my best to
answer them! I'll also try and put up a page sometime this week
with more details. If you miss out on this batch, don't worry!
I'll definatelly be making more every month, and hopefully more
than just four at a time as well.

12:00 PM on saturday the 25th, send me an email stating you'll buy
one right away!

I think for the next batch, I'll get the boxes predrilled and powdercoated.

Hollow Earth PCBs..

2009-07-15T10:26:00.000-07:00

..are in

Hollow Earth (final) v3

2009-07-09T21:12:00.000-07:00

It's coming and non-blems will be $200 US. I've set up an email list to inform people a week or two in advance when the first (small) batch goes up, so if you'd like to be informed, shoot me an email at

eblythe
aaaaat
mochamail.com

I'm just waiting for the PCBs. Probably a week or a little over from now. Once I recieve them, I'll send an email to everyone with more info.

DIY Jawari build

2009-06-09T17:13:00.000-07:00

My fourth, exactly...

Schematic found near the bottom of this fine page

Samplerate reducer + resonant LPF

2009-06-02T18:09:00.000-07:00

Just a rehouse of the blue samplerate reducer/LPF I build several months ago. Was never a huge fan of the original paintjob.

Hollow Earth (v2)

2009-05-08T19:42:00.000-07:00

First prototype of v2 is done. Things to do include minor software tweaks, getting expression-out working, cosmetic changes. I figure I'll have a small batch of these available for around $200-225 US in july/august.

Hollow Earth v2 - populated PCB

2009-04-30T19:57:00.000-07:00

Hollow Earth v2?

2009-03-30T20:01:00.000-07:00

Alright.....

I posted the video sample and details of that Hollow Earth pedal I built a couple weeks ago on about 5 forums. It went slightly viral on a few others thanks to a few users. Anyways, interest in it has been a little overwhelming! So much so that I've convinced myself that I should build a batch of revisions of this to spread around.

Things I'd like to add/change:
-Eight to ten presets, all overwritable with your own shapes
(with LED digit display)
-Expression-in for the shaping
-Expression-out to "shape" other effects
-Rugged footswitch for record instead of the flimsy button
-Random mode
-Triggered envelope mode
-Sample input as waveshape
(the last one is a biiiig maybe)

After a 10-day break from this stuff to play jams/gigs, I started tinkering again. I got random mode mostly working, and I've started the preset saving bit. 8 pin DIP 24LC eeproms are a wonder!

Hollow Earth video demo

2009-03-21T14:36:00.000-07:00

Hollow Earth waveshaper

2009-03-19T21:07:00.001-07:00

You know that feature the Goatkeeper has? Waveshaping? "design" your own LFO and then use that as a trem? Yeah, that. But a bit more!

Hold down the "record" pushbutton, "draw" out an LFO/envilope shape with the "shape" knob (it can be several seconds long), and release the button for it to start looping the shape and modulate the volume of whatever instrument you have plugged through it. AKA "tremolo". Push button again to design a new one. [U]Or[/U]! Or toggle "punch-in" switch to edit the existing shape with whatever you feel! "smotheness" knob makes it smooth if the waveshape sampling feels a bit too steppy/aliased. It happens if you sample at a very slow tempo and keep it very slow. "speed" accelerates or decelerates the LFO. I forget what "volume" does.

Two LEDs on either side of the bypass switch (under the decals/finish). The one on the right follows your wave "drawing" as well as when it's looping. "firmware upgradeable"

Video sample tomorrow.

AVR programming and effect automation...

2009-03-15T16:53:00.000-07:00

If there's one thing I'm really bad at, really really really bad at, when it comes to electronics, it's control logic. The little bits that need specific timing, when to do such thing and when not to do it, if voltage dips below X then do so-and-so, etc, that kind of crap. Using traditional logic chips, I just can't get my head around it. Ever. I've also been wanting to integrate more automation in my synths/pedals. Thus, easy to program AVR microcontrollers have been interesting me as of late.

Here is the kit I've just purchased (thing on the left):

I did a lot of Basic programming in school. QBasic, Visual Basic, etc. It's pretty easy stuff compared to assembly or even C. Microcontrollers at first seemed daunting to me because I wasn't prepared to learn any good language, but then I found out that these little AVR chips can be programmed from a Basic environment called BASCOM! It took me a few days to get serial com to work (had to go out and buy a serial PCI card, the USB-to-serial adapter I had was rubbish, I found out days later). Once I was up and running though, it was pretty easy to get basic things going. Blinking lights, input, potentiometer reading (ADC) and PWM (sPitting out Waves that I can use for Modulation or whatever).

The little project in the photo is something I started today. It's one push-button, two potentiometers and a LED, all hooked up to the programmer. I got it so that pushing the button will make the MCU go into "record mode", where it will record pot-twisting for up to several seconds (one byte per sample at 60 sampels a second). As soon as I let go of the button, or if the severa lsecond limit runs out, it loops the recorded twisting which can be observed through the LED! The other pot can adjust the speed of playback/record.

This opens up all sorts of fun additions to effects! I could for instance "record" a certain knob on a delay or synth, and have it automatically loop! Exciting stuff! Once content with my program, pop the chip out of the programmer (that long chip in the center) and stick it in my own circuit. Done!

They make smaller chips. I'll get different sizes depending on how I need them.

new build

2009-02-16T04:08:00.000-08:00

simplified TS clone with a few mods

Tremulus Lune

2009-02-07T22:42:00.001-08:00

the Tremulus Lune is a popular DIY tremolo design. I've already bought the one with speed modulation straight from 4ms (who are an awesome company with awesome philosophies), but sometimes I need a minimal one that doesn't take up the space of 4 regular-sized pedals. hence I made this.

two LEDs. the red one is bypass LED, and the yellow one blinks the shape and speed of the trem (even when bypassed). the LEDs are *under* the finish too, so it's quite seamless!

commonsound layout. the gain pot is inside because I have no use for that when playing. I have it set as very slightly louder than bypassed, to make up for the dips in the trem modulation. I accidentally etched the PCB backwards, and was too lazy to re-etch it. so I just populated everyhting on the "wrong" side of the PCB.

I drew the girl. the patterns were "found". paints are acrylics and mostly painted on with a toothbrush. everything coated with clear epoxy resin.

2009-01-27T19:28:00.000-08:00

samplerate reducer 99% finished!

2009-01-26T20:11:00.000-08:00

still not named as of yet

sound/video clips maybe tomorrow if I find my camera (the one that does video). still needs a bit of tweaking. LPF resonance can get loud at times so I'm gonna hook up clipping diodes. resonance pot is also wired backwards, and I want to paint lines o nthe knobs!

yet-to-be-named bitcrusher

2009-01-25T12:44:00.001-08:00

the ringmod from two weeks ago is being broken-in by a buddy so I had a bit of time to do something different. bitcrusher/samplerate-reducer type effect! this sports the taditional atari-ish samplerate reduction sound, a break knob that makes it spazz out in a cool way and a droning resonant low-pass filter. also blend control and a noise gate.

it's also my first project where I didn't touch the PCB autorouter....

the epoxy coat takes about 24 hours to harden before I can comfortable handle it. I'll try to populate the board before then.

Turmoil 2 proto

2009-01-04T12:10:00.000-08:00

It's aliiive!

Blend control isn't working for some reason, but otherwise it's working. Doesn't seem to like onespot power supplies though! At all! Works fine with my Diago though. onespot sucks!

Clips when I get blend working.

Turmoil ringmodulator running...

2008-12-31T13:38:00.000-08:00

I found a bit of time to redo the design of a ringmod I built exactly last year. This new one has an added lowpass filter, fine-tuning control and expression pedal support for the frequency. I've also improved the noise gate enough that I no longer need a control pot for calibration. It sounds much better! Carrier bleed is pretty-much non-existant even with high-frequencies. I've removed triange/squarewave blending because square wasn't very interesting and in fact worstened the bleed.

Over the next few days, I will be drawing up a PCB layout and hopefully building a final prototype before I make batches of these.

Happy new year!

another Dying Sonar video

2008-12-22T17:59:00.000-08:00

First 3 minutes are random noodling/bad playing. I was playing better earlier today, honest! Then for 30 seconds I'm having trouble with the sound. After that it's all drone. Main purpose of the video is to show how it interacts with a guitar.

Dying Sonar pedal synth

2008-12-21T19:39:00.000-08:00

Have a little time this xmas holiday and I'm not quite inspired enough yet to start doing the PCB layout for my massive dronebox project, so I started something easier.

It's a simple idea. Make an oscillator (I used the ones I fixed up for the dronebox project), make an LFO (based on part of the Tremulus Lune and somewhat modified) and have the LFO modulate the volume of the oscillator. And make it in stompbox format.

It can either be an instrument or a pedal somewhere in the middle of the chain. It does absolutelly nothing to the guitar signal that passes through it. It will add pulsating beeps, drones, tones how fast and how slow you want them. It's great for electroacoustic/ambient sets where you need a rythmic bassy tone in the background! Loop it, and all kind of layering possibilities open up! The controls are as follows:

Volume: volume. does not affect passing-through guitar signal.
Smooth: blends between sawtooth and squarewave LFO
Space: space between pulses less or more
Speed: tempo of the LFO. extremelly slow (like 2 BPM) to way too fast (pulses smeared together)
Shape: oscillator shape blends between triangle and square
Freq: frequency of oscillator. used with Range toggle switch will get you anything between 10Hz to >18KHz

Paints are acrylic and the finish is clear epoxy resin. It has a couple impendance and volume problems which I need to fix, but it works okay if you don't use an amp. Here's a brief video with me goofing off on it:

drone box preview

2008-11-29T19:51:00.000-08:00

drone box. it's a synth, basically. designed to make walls of tones and drones!

not really based on any existing circuit. it's a bunch of simple ideas that will all be wired together in weird ways. at first it was going to be pseudo-modular but decided I'd rather mess with well-planned switching and relays instead. here's how it basically functions:

6 oscillators each with a wide frequency range, fine-tuning and triangle-square shape control. sub brings the range down to literally pulsating textures (less than 1hz in frequency). the highest is ear-shattering/borderline off human-hearing. each oscillator can independantly and selectivly be pitch-modulated by either of the two sequencers. each sequencer can be hard-synched or independant. portamento blends the steps so that they flow more naturally if wanted. either sequencer can be set to loop or to be triggered. if triggered, it stops after the eighth step. each oscillator can be independantly panned (left to right) and mixed to a final stereo mix for potentially wicked awesome stereo soundscapes! the final stereo mix volume can be modulated by either of the two sequencers as well.

a bit of technical info: oscillators are opamp based. I use tl072s. sequencers are just 4017s. I use vactrols to modulate stuff around.

Voetsek tremolo DIY guide..

2008-11-22T07:16:00.000-08:00

Some people have asked for a guide for that insane 16-step tremolo I built. Here's an archive with the guide as well as PCB transfers in 600dpi. I'll be the first to admit that this circuit needs some tweaks and could be much better! I'm learning about this stuff, and I'll make a better one sometime.

Cacophonator build

2008-11-18T20:02:00.000-08:00

Built a Cacophonator for someone. Needless to say, I'm going to miss it!

Here's a 4-minute sample:
cacophonator_sample_01.mp3

Blog-doing

2008-11-15T07:46:00.000-08:00

In the last few years, effect-making has rapidly become a near-obsession of mine! Because I had been posting these personal creations in various places on the internet, people were starting to take genuine interest. This blog is an effort to keep them informed of any custom jobs or short runs I might make, and to keep me organized.

I'm by no means an expert. This is relitavelly new to me! My builds are still a mess inside, and I frequently annoy pros on how to do this-and-that's. I am getting better though, and I think I've gotten up to a level where I'm confident enough to build a few, sell, and not worry too much about the reliability or robustability of the paintwork.

A familly photo of those I've made. Doesn't include the ones I later dismantled for parts.

A lot are based heavily off existing designs and were excersises in making them look pretty or understanding how they work. Others (top-left, top-center, top-right, bottom-second and third) are original designs. I'm most likely to make a batch of the ringmod (white with all the circles) for those interested, as well as several little feedback loopers like the one at top-right.

I'll update this blog with ideas, finds, prototypes, samples and others' works of interest!